Clean the elevator and the elevator hall
Elevator hall is clean and free of any debris, walls smooth, transparent mirror-bright, no stains, no fingerprints bright stainless steel part.
Generally short steps:
(1) the night of the hall and the walls and floor of the elevator full of wiping, such as elevator door, the car walls, (public micro-channel number: Elevator) ladder inside mirror, ceiling, lighting and carpet suck dust and so on.
(2) during the day to keep the cycle of escalators hall, keys, door mirror or the walls and floor were cleaning, keep the lift clean, tidy and free of dirt.
(3) frequent cleaning trash and cigarette butts in the ashtray of the elevator.
(4) the elevator at night on a regular basis for cleaning, maintenance, including the wall of the elevator door waxing polishing.
(5) Every morning carpet for once, if necessary, increase the number of replacement.
First, the elevators are clean
Features: elevators operating mode is a vertical run, sub passenger and cargo lift two kinds. Which basically are equipped with cameras, lighting, signs nameplates, car sub-prime steel mirror steel and two materials. Bottom compartment usually stone floors, carpeted.
1, tools and equipment ready: aluminum ladder, towels, lens cloth, pressing buckets, blades, vacuum cleaner, mop, working signs, big mouth folder.
2, materials and deployment: water that day, All Purpose Cleaner, stainless steel oil, steel mirror oil, prime steel oil, air fresheners, cleaning agents.
3, operating procedures:
1) Please shut down the elevator with the engineering department, place "is clean, suspended" warning signs in the elevator door.
2) With the aluminum ladder to clean the car top smallpox.
3) vacuum the carpet clean of dust, slot car tracks in the sand lime, and wipe it with a wet towel. 4) The lens cloth folded into four, with a big mouth and clamp onto, even after spraying stainless steel oil shake the lens cloth, wipe the stainless steel along the grain direction, each time to avoid missing a small portion of the overlap. After the lens cloth to wipe the dirty side, and replaced with the other side. (Rotating stainless steel oil depending on the type of stainless steel, steel mirror mirror on the choice of steel oil, prime steel on steel oil-selectin).
5) with a razor blade to scrape the bottom floor of the car chewing gum tracks, and then offset removing water that day.
6) After mop sucked through the deployment of a good cleaning fluid squeezed juice with buckets, dragging the net of the car to the ground.
7) the carpet back into place gracefully.
8) cleaning, pick up tools neatly back into place regulations, towels, spare lens cloth dry cleaned.
9) removed the warning signs, call engineering staff to open the elevator.
4 Notes:
1) Do not wipe with a hard steel surface mirror crude fiber towel to avoid scratch.
2) Top car wash ceiling lighting is very complex, can only be carried out in the engineering and technical personnel in coordination with removable side, so as not to damage the lamps.
3) If the elevator without air vents, After cleaning, spray air freshener.
4) Before using stainless steel oil and shake cans.
Correct use
Second, escalator cleaning:
Features: escalators by handrails, bumpers, skirts, stepped a few parts, cracks more easily accumulate loot.
1, tools and equipment ready: towels, mops, vacuum cleaners, buckets, blades, brooms, garbage shovel work warning signs, painted water heater, wipers.
2, materials and deployment: All Purpose Cleaner, water that day, stainless steel oil, deployment methods.
3, operating procedures:
1) Requirements engineering and technical personnel to stop the elevator lift.
2) The two were put to work in the elevator warning signs.
3) order the stage with a broom sweep lift crude garbage debris.
4) with a razor blade to scrape stick in the elevator before the pedal, as well as chewing gum on the steps of the track, and with water that day to remove the offset.
5) The deployment of a good all-around with a towel soaked in cleaning solution, wring, folded into eight layers, wiping handrails and fences. Towel to wipe the dirty side of the face so as not to continue for another rub until all are finished with the mop. After the clean towels in the same way the armrest and the tailgate.
6) with a thin towel, wipe the oil stainless steel baffle, or coated with water, glass scraper clean glass tailgate.
7) with a mop soaked versatile cleaning solution, wring net drag lift pedal and front steps.
8) operation is completed, clean paraphernalia neatly back provisions, towels. Broom clean dry spare, removed the signs, open elevator.
4 Notes:
1) Do not wipe plastic armrest with water that day (aka banana water).
2) When cleaning the stairs, do not ignore the steps Plessis